How to Install Artificial Turf: A Step-by-Step Guide

Artificial turf installed in a backyard

Installing synthetic grass is one of the most satisfying home projects you can take on, and one of the easiest to get wrong. The turf itself is only part of the result. How well your lawn drains, lies flat, holds its seams, and looks in five years comes down to what happens before the first roll comes off the truck. Whether you're researching artificial turf installation for a weekend DIY project or trying to understand what a professional crew will do, this guide walks through every step, from planning and base preparation to seams, edges, and infill.

Quick answer: to install artificial turf, you (1) plan and measure the area, (2) excavate and remove vegetation, (3) build a compacted, sloped aggregate base, (4) roll out and acclimate the turf, (5) cut and seam it, (6) secure the edges, (7) add infill if your product calls for it, and (8) brush and groom the finished surface. Of those, base preparation is the step most likely to make or break the result.

Before You Start: Plan the Project

Check Rules and Utilities

Before you dig, find out whether your homeowners association, city, or landlord has requirements for turf. In the United States, call 811 a few days before you dig so underground utilities can be marked. Note where irrigation lines, drains, and downspouts run, since you'll need to cap, reroute, or accommodate them. If you plan to build a pool surround, playground, or putting green, those uses come with their own considerations, so read the matching guide or talk to us first.

Choose the Right Turf for the Job

Installation details vary a little depending on the product, so choose your turf first. As a quick reference:

  • PETMAXX and AQUAMAXX are fast-draining turf for pet areas, lawns, pool surrounds, and playgrounds, and they call for infill.
  • HEATMAXX SOFT is soft-feel nylon turf for lawns, rooftops, and indoor and outdoor spaces, and it requires no infill.
  • SPORTMAXX is golf and sport turf for putting greens, tee lines, and flooring, with infill either optional or not accepted depending on the product.
  • The Value Series is our economical landscape line, with specifics listed on each product page.

Measure Carefully

Measure the length and width of your area, and sketch the shape on paper. Go Green's landscape and sport turf comes in 15 ft wide rolls (the Value Series offers 6 ft and 12 ft widths), so think about how the rolls will lie across the space and where seams will fall. Full rolls are 100 linear feet for most lines and 200 linear feet for SPORTMAXX 36 putting turf, and cut lengths from 20 to 80 linear feet are available for smaller projects. Add a few extra inches on each side for trimming, and order a bit more than you think you need.

Pay Attention to Grain Direction

Turf fibers lean slightly in one direction, called the grain or nap. All pieces should be laid with the grain facing the same way, usually toward the main viewing point, so the color and sheen match across seams. If you rotate one piece, it will look like a different shade.

Tools and Materials Checklist

Category What You'll Need
Excavation Flat shovel, rake, wheelbarrow, sod cutter (for larger areas), string line and stakes
Base Crushed aggregate, plate compactor, hand tamper for edges, screed board, level
Weed control Geotextile fabric or weed barrier (optional but common)
Turf work Utility knife with spare blades, tape measure, straightedge, chalk or marker
Seams Seam tape, turf adhesive, trowel, weights or sandbags
Edges Landscape nails or spikes, hammer, edge restraint or bender board
Infill Infill (if required), drop spreader, power broom or stiff synthetic-bristle brush
Safety Gloves, eye protection, knee pads, dust mask, sturdy boots

Step 1: Remove Existing Grass and Excavate

Strip away existing sod, weeds, and roots from the entire installation area. A sod cutter makes quick work of large lawns. Then excavate to the depth you need. The final depth depends on your base thickness plus a little room for the turf and infill, and many residential installers excavate roughly three to four inches, adjusting for soil conditions and use. Soft or clay soils, high-traffic areas, and sites that stay wet often call for a thicker base, and your installer can advise on what makes sense for your site.

Remove rocks, roots, and debris as you go, and check for any irrigation heads or pipes that need to be capped or relocated.

Step 2: Add a Weed Barrier (Optional)

Many installers lay a geotextile fabric over the excavated soil before adding aggregate. It helps separate the base from the soil beneath and slows weed growth coming up from below. Overlap the edges of the fabric and make sure it lies flat. It's not required for every project, but it's a common and inexpensive layer.

Step 3: Build and Compact the Base

This is the foundation of your installation, and it deserves the most time. The base does three things: it gives the turf a stable, even platform; it provides a path for water to drain away; and it keeps the surface from settling and developing dips over time.

Choose and Spread the Aggregate

Most installations use crushed aggregate, such as crushed stone or decomposed granite, which compacts firmly and drains. Spread it in layers, typically in lifts of an inch or two, and compact each layer before adding the next. A plate compactor does this far better than a hand tamper, and renting one is worth it.

Create a Gentle Slope

The base should slope slightly away from buildings and toward a drainage point, so water has somewhere to go. A slope of around one percent is a common target, which works out to roughly an eighth of an inch per foot. Use a string line and a level to check the grade as you work.

Finish With a Smooth, Firm Surface

Screed the top of the base to a smooth, uniform finish, then compact it one last time. Lightly misting the base with water can help the top layer lock together. Run your hand over it and look for dips, humps, and loose spots, since turf will show whatever lies beneath it. For putting greens, tee lines, and play surfaces, this finishing step matters even more.

Step 4: Roll Out and Acclimate the Turf

Unroll the turf in its final position and let it relax, ideally for a few hours in warm weather, so it lies flat and the wrinkles from shipping settle out. On hot days, handle the turf carefully, since the backing can be hot to the touch. Make sure all pieces face the same direction, and make sure the rolls overlap the edges slightly.

Ideally, turf should be moved by lifting, not dragging, which can distort the backing or pull fibers. Roll or fold it back as needed.

Step 5: Cut and Fit

Trim the turf to fit around the edges of your area, working from the back of the turf with a sharp utility knife and cutting between rows of stitches so you don't cut the fibers on the face. Change blades often, since dull blades snag and tear. Cut a bit at a time and test the fit. You can always trim more, but you can't put it back.

For curves, make relief cuts and trim gradually. For borders around trees, posts, or pavers, leave a small margin you can finish later.

Step 6: Seam the Turf

Wherever two pieces meet, the seam needs to be tight, flat, and well adhered. A bad seam shows up as a visible line, a gap, or an edge that lifts. A good seam disappears.

Prepare the Edges

Trim the factory edges of both pieces, removing the selvage or any rows of damaged stitches, so the two pieces will meet cleanly. Butt the edges together and make sure the stitch rows are evenly spaced across the seam, so there's no visible gap in the pattern.

Place the Seam Tape and Adhesive

Fold the edges back and lay seam tape on the base beneath where the seam will fall, centered under the joint. Apply turf adhesive to the tape according to the manufacturer's instructions, spreading it evenly with a trowel. Then fold the edges of the turf back down onto the adhesive, one piece at a time, and be sure no fibers get caught in the glue. Follow the adhesive manufacturer's directions for working time and cure time.

Weight and Check

Place weights, such as sandbags, along the seam to hold it in contact with the adhesive while it cures. Once it's set, brush the fibers across the seam so they stand up and blend. If you see any gaps, correct them now, before moving on.

Step 7: Secure the Edges

Edges are where turf most often lifts or curls. Secure the perimeter with landscape nails or spikes, spaced closely enough to hold the edge firmly, and drive them so the heads sit flush with the backing. For a cleaner and longer-lasting finish, many installers add a rigid edge restraint, such as bender board or a concrete or paver border. Along existing paving, nail directly into the base next to the edge. Choose the right edging method for your site: it matters most around pools, play areas, and high-traffic paths.

Step 8: Add Infill (If Your Turf Needs It)

Infill helps hold the fibers upright, adds weight and stability, and affects performance and feel. But not every turf uses it, so follow the guidance for your specific product.

Turf Infill
AQUAMAXX 50 / PETMAXX 50 Approximately 1 lb/sq ft, with EnviroFill 12-20 recommended
AQUAMAXX / PETMAXX 75 and 90 Approximately 3 lb/sq ft, with EnviroFill 12-20 recommended
HEATMAXX SOFT 47 / 65 None required
SPORTMAXX 36 2CN / 3CN Not required. Compatible putting-green infill may be used if preferred
SPORTMAXX 100 None. This turf does not accept infill
Value Series See the product page for current requirements

How to Apply Infill

Spread infill evenly using a drop spreader, in several light passes instead of one heavy one. After each pass, work it into the fibers with a power broom or a stiff synthetic-bristle brush, brushing against the grain so the fibers stand up. Keep going until you've applied the recommended amount and the infill is distributed evenly. Uneven infill leads to uneven wear and appearance.

EnviroFill 12-20's rounded, uniform granules settle in quickly and evenly, and its built-in antimicrobial protection is a helpful feature in pet areas. For more on infill, see our guide to EnviroFill.

Step 9: Final Grooming

Give the finished surface one more thorough brushing, against the grain, to lift the fibers and even out the infill. Walk the area looking for seams that need attention, edges that need another nail, and spots where infill is thin. Rinse the turf lightly with a hose to settle everything, and clear away any debris from the job.

Product-Specific Installation Notes

Pet Areas and Pool Surrounds (PETMAXX and AQUAMAXX)

These lines are built for fast drainage and drain at greater than 600 in/hr, but they work best over a well-prepared, draining base. Slope and outlets matter most in pet runs and pool surrounds, where water volume is high. Plan your slope and base accordingly.

Heat-Exposed Areas and Rooftops (HEATMAXX SOFT)

HEATMAXX SOFT requires no infill and is certified for indoor, exterior, and rooftop applications. For rooftops and decks, drainage design and the substrate need extra care, so involve your installer, and confirm any building or fire-code requirements with your local authority.

Putting Greens and Golf Surfaces (SPORTMAXX)

Putting surfaces reward precision. A firm, level, well-compacted base and flawless seams are what make a ball roll true. If you're building a putting green, read our backyard putting green guide before you start.

Common Installation Mistakes to Avoid

  • Skimping on the base. A thin, uncompacted, or uneven base leads to dips, wrinkles, and drainage trouble.
  • Ignoring slope. Without a gentle slope, water can sit on top of the base even under fast-draining turf.
  • Mismatched grain direction. Pieces turned different ways look like different colors.
  • Rushing the seams. Gaps, glue on the fibers, and rushed curing show up as visible lines.
  • Under-securing the edges. Perimeters lift if they aren't fastened or restrained.
  • Applying infill unevenly or in the wrong amount. Follow the product guidance.
  • Cutting from the face. Cutting through fibers leaves visible gaps. Cut from the back.
  • Working in extreme heat. Hot backing can be hard to handle, and adhesives cure differently in different weather.

DIY or Professional Installation?

Many homeowners successfully install small, simple, flat areas themselves. A professional crew is worth considering for larger projects, complex shapes, contoured putting greens, playground fall protection, rooftops, and commercial installations, or whenever the warranty and long-term performance are high priorities. Professionals bring compaction equipment, seaming experience, and drainage know-how, and a great base is hard to fake.

You can also split the work: hire a pro to build the base and do the seams, and handle the final finishing yourself. Whatever you choose, remember that installed performance depends on base preparation, drainage design, seaming, infill, and maintenance, not on the roll alone.

What Affects Installation Cost?

We don't publish installation pricing here because it varies widely, but the main factors are consistent. They include the size of the area, how much excavation and base material your site needs, drainage work, access for equipment, the complexity of the shape, edging choices, infill requirements, and whether you're paying for labor. Get quotes from installers in your area, and contact us for current turf pricing.

After Installation

In the first few weeks, brush the turf periodically and watch for any settling, edge lifting, or seam issues, so small problems get fixed early. After that, a simple routine of removing debris, rinsing, brushing, and checking infill keeps the lawn in good shape. See our complete guide to cleaning and maintaining artificial turf for details.

Keep your proof of purchase and review your warranty. Our products are backed by limited prorated warranties, such as the 15-year limited prorated warranty on AQUAMAXX, PETMAXX, HEATMAXX SOFT, and SPORTMAXX, subject to the written warranty's exclusions, original-purchaser requirement, and claim timing.

Frequently Asked Questions

How do you install artificial turf on dirt?
Remove the grass and vegetation, excavate, add a compacted aggregate base sloped for drainage, lay the turf, seam and secure it, and add infill if your product needs it. Don't lay turf straight on bare soil, since it won't drain or stay level.

How deep should the base be?
It depends on your soil, drainage, and use. Many residential installers use a few inches of compacted aggregate, with more for soft soils or heavy-use areas. Ask an installer about your site.

Can you install artificial turf over concrete?
Often yes, if the surface is sound, clean, and drains, or has drainage provisions. Some products and uses, like rooftops and indoor installs, have specific requirements, so ask us.

How do you seam artificial turf?
Trim the edges so they meet cleanly, lay seam tape beneath the joint, apply turf adhesive, press the edges down into it without catching fibers, weight the seam while it cures, and brush the fibers across it.

Do I need infill?
It depends on the product. PETMAXX and AQUAMAXX call for it, HEATMAXX SOFT and SPORTMAXX 100 don't use any, and SPORTMAXX 2CN and 3CN treat it as optional.

Ready to Start Your Project?

A good installation starts with the right product and a plan. Browse the Go Green lineup, or contact our team with your measurements and your project goals, and we'll help you choose turf, infill, and the right quantities.